Codex

PACKET

Section: Linux Programmer's Manual (7)

Updated: 2014-08-19

Index?action=index Return to Main Contents


NAME

packet - packet interface on device level

SYNOPSIS

#include <sys/socket.h>

#include <linux/if_packet.h>

#include <net/ethernet.h> /* the L2 protocols */ packet_socket = socket(AF_PACKET, int socket_type, int protocol);

@]

DESCRIPTION

Packet sockets are used to receive or send raw packets at the device driver (OSI Layer 2) level. They allow the user to implement protocol modules in user space on top of the physical layer.

The socket_type is either SOCK_RAW for raw packets including the link-level header or SOCK_DGRAM for cooked packets with the link-level header removed. The link-level header information is available in a common format in a sockaddr_ll. protocol is the IEEE 802.3 protocol number in network byte order. See the <linux/if_ether.h> include file for a list of allowed protocols. When protocol is set to htons(ETH_P_ALL) then all protocols are received. All incoming packets of that protocol type will be passed to the packet socket before they are passed to the protocols implemented in the kernel.

Only processes with effective UID 0 or the CAP_NET_RAW capability may open packet sockets.

SOCK_RAW packets are passed to and from the device driver without any changes in the packet data. When receiving a packet, the address is still parsed and passed in a standard sockaddr_ll address structure. When transmitting a packet, the user supplied buffer should contain the physical layer header. That packet is then queued unmodified to the network driver of the interface defined by the destination address. Some device drivers always add other headers. SOCK_RAW is similar to but not compatible with the obsolete AF_INET/SOCK_PACKET of Linux 2.0.

SOCK_DGRAM operates on a slightly higher level. The physical header is removed before the packet is passed to the user. Packets sent through a SOCK_DGRAM packet socket get a suitable physical layer header based on the information in the sockaddr_ll destination address before they are queued.

By default all packets of the specified protocol type are passed to a packet socket. To get packets only from a specific interface use bind?(2) specifying an address in a struct sockaddr_ll to bind the packet socket to an interface. Only the sll_protocol and the sll_ifindex address fields are used for purposes of binding.

The connect?(2) operation is not supported on packet sockets.

When the MSG_TRUNC flag is passed to recvmsg?(2), recv?(2), recvfrom?(2) the real length of the packet on the wire is always returned, even when it is longer than the buffer.

Address types

The sockaddr_ll is a device independent physical layer address.

sll_protocol is the standard ethernet protocol type in network byte order as defined in the <linux/if_ether.h> include file. It defaults to the socket's protocol. sll_ifindex is the interface index of the interface (see netdevice?(7)); 0 matches any interface (only permitted for binding). sll_hatype is an ARP type as defined in the <linux/if_arp.h> include file. sll_pkttype contains the packet type. Valid types are PACKET_HOST for a packet addressed to the local host, PACKET_BROADCAST for a physical layer broadcast packet, PACKET_MULTICAST for a packet sent to a physical layer multicast address, PACKET_OTHERHOST for a packet to some other host that has been caught by a device driver in promiscuous mode, and PACKET_OUTGOING for a packet originated from the local host that is looped back to a packet socket. These types make sense only for receiving. sll_addr and sll_halen contain the physical layer (e.g., IEEE 802.3) address and its length. The exact interpretation depends on the device.

When you send packets it is enough to specify sll_family, sll_addr, sll_halen, sll_ifindex. The other fields should be 0. sll_hatype and sll_pkttype are set on received packets for your information. For bind only sll_protocol and sll_ifindex are used.

Socket options

Packet socket options are configured by calling setsockopt?(2) with level SOL_PACKET.

:PACKET_ADD_MEMBERSHIP

PACKET_DROP_MEMBERSHIP
Packet sockets can be used to configure physical layer multicasting and promiscuous mode. PACKET_ADD_MEMBERSHIP adds a binding and PACKET_DROP_MEMBERSHIP drops it. They both expect a packet_mreq structure as argument:

mr_ifindex contains the interface index for the interface whose status should be changed. The mr_type parameter specifies which action to perform. PACKET_MR_PROMISC enables receiving all packets on a shared medium (often known as "promiscuous mode"), PACKET_MR_MULTICAST binds the socket to the physical layer multicast group specified in mr_address and mr_alen, and PACKET_MR_ALLMULTI sets the socket up to receive all multicast packets arriving at the interface.

In addition, the traditional ioctls SIOCSIFFLAGS, SIOCADDMULTI, SIOCDELMULTI can be used for the same purpose.

:

PACKET_AUXDATA (since Linux 2.6.21)
If this binary option is enabled, the packet socket passes a metadata structure along with each packet in the recvmsg?(2) control field. The structure can be read with cmsg?(3). It is defined as
:
PACKET_FANOUT (since Linux 3.1)
To scale processing across threads, packet sockets can form a fanout group. In this mode, each matching packet is enqueued onto only one socket in the group. A socket joins a fanout group by calling setsockopt?(2) with level SOL_PACKET and option PACKET_FANOUT. Each network namespace can have up to 65536 independent groups. A socket selects a group by encoding the ID in the first 16 bits of the integer option value. The first packet socket to join a group implicitly creates it. To successfully join an existing group, subsequent packet sockets must have the same protocol, device settings, fanout mode and flags (see below). Packet sockets can leave a fanout group only by closing the socket. The group is deleted when the last socket is closed.

Fanout supports multiple algorithms to spread traffic between sockets. The default mode, PACKET_FANOUT_HASH, sends packets from the same flow to the same socket to maintain per-flow ordering. For each packet, it chooses a socket by taking the packet flow hash modulo the number of sockets in the group, where a flow hash is a hash over network-layer address and optional transport-layer port fields. The load-balance mode PACKET_FANOUT_LB implements a round-robin algorithm. PACKET_FANOUT_CPU selects the socket based on the CPU that the packet arrived on. PACKET_FANOUT_ROLLOVER processes all data on a single socket, moves to the next when one becomes backlogged. PACKET_FANOUT_RND selects the socket using a pseudo-random number generator. PACKET_FANOUT_QM (available since Linux 3.14) selects the socket using the recorded queue_mapping of the received skb.

Fanout modes can take additional options. IP fragmentation causes packets from the same flow to have different flow hashes. The flag PACKET_FANOUT_FLAG_DEFRAG, if set, causes packet to be defragmented before fanout is applied, to preserve order even in this case. Fanout mode and options are communicated in the second 16 bits of the integer option value. The flag PACKET_FANOUT_FLAG_ROLLOVER enables the roll over mechanism as a backup strategy: if the original fanout algorithm selects a backlogged socket, the packet rolls over to the next available one.

:

PACKET_LOSS (with PACKET_TX_RING)
When a malformed packet is encountered on a transmit ring, the default is to reset its tp_status to TP_STATUS_WRONG_FORMAT and abort the transmission immediately. The malformed packet blocks itself and subsequently enqueued packets from being sent. The format error must be fixed, the associated tp_status reset to TP_STATUS_SEND_REQUEST, and the transmission process restarted via send?(2). However, if PACKET_LOSS is set, any malformed packet will be skipped, its tp_status reset to TP_STATUS_AVAILABLE, and the transmission process continued.:
PACKET_RESERVE (with PACKET_RX_RING)
By default, a packet receive ring writes packets immediately following the metadata structure and alignment padding. This integer option reserves additional headroom.:
PACKET_RX_RING
Create a memory-mapped ring buffer for asynchronous packet reception. The packet socket reserves a contiguous region of application address space, lays it out into an array of packet slots and copies packets (up to tp_snaplen) into subsequent slots. Each packet is preceded by a metadata structure similar to tpacket_auxdata. The protocol fields encode the offset to the data from the start of the metadata header. tp_net stores the offset to the network layer. If the packet socket is of type SOCK_DGRAM, then tp_mac is the same. If it is of type SOCK_RAW, then that field stores the offset to the link-layer frame. Packet socket and application communicate the head and tail of the ring through the tp_status field. The packet socket owns all slots with tp_status equal to TP_STATUS_KERNEL. After filling a slot, it changes the status of the slot to transfer ownership to the application. During normal operation, the new tp_status value has at least the TP_STATUS_USER bit set to signal that a received packet has been stored. When the application has finished processing a packet, it transfers ownership of the slot back to the socket by setting tp_status equal to TP_STATUS_KERNEL. Packet sockets implement multiple variants of the packet ring. The implementation details are described in Documentation/networking/packet_mmap.txt in the Linux kernel source tree.:
PACKET_STATISTICS
Retrieve packet socket statistics in the form of a structure

Receiving statistics resets the internal counters. The statistics structure differs when using a ring of variant TPACKET_V3.

:

PACKET_TIMESTAMP (with PACKET_RX_RING; since Linux 2.6.36)
The packet receive ring always stores a timestamp in the metadata header. By default, this is a software generated timestamp generated when the packet is copied into the ring. This integer option selects the type of timestamp. Besides the default, it support the two hardware formats described in Documentation/networking/timestamping.txt in the Linux kernel source tree.:
PACKET_TX_RING (since Linux 2.6.31)
Create a memory-mapped ring buffer for packet transmission. This option is similar to PACKET_RX_RING and takes the same arguments. The application writes packets into slots with tp_status equal to TP_STATUS_AVAILABLE and schedules them for transmission by changing tp_status to TP_STATUS_SEND_REQUEST. When packets are ready to be transmitted, the application calls send?(2) or a variant thereof. The buf and len fields of this call are ignored. If an address is passed using sendto?(2) or sendmsg?(2), then that overrides the socket default. On successful transmission, the socket resets tp_status to TP_STATUS_AVAILABLE. It immediately aborts the transmission on error unless PACKET_LOSS is set.:
PACKET_VERSION (with PACKET_RX_RING; since Linux 2.6.27)
By default, PACKET_RX_RING creates a packet receive ring of variant TPACKET_V1. To create another variant, configure the desired variant by setting this integer option before creating the ring.:
PACKET_QDISC_BYPASS (since Linux 3.14)
By default, packets sent through packet sockets pass through the kernel's qdisc (traffic control) layer, which is fine for the vast majority of use cases. For traffic generator appliances using packet sockets that intend to brute-force flood the network---for example, to test devices under load in a similar fashion to pktgen---this layer can be bypassed by setting this integer option to 1. A side effect is that packet buffering in the qdisc layer is avoided, which will lead to increased drops when network device transmit queues are busy; therefore, use at your own risk.:

Ioctls

SIOCGSTAMP can be used to receive the timestamp of the last received packet. Argument is a struct timeval variable.

In addition, all standard ioctls defined in netdevice?(7) and socket?(7) are valid on packet sockets.

Error handling

Packet sockets do no error handling other than errors occurred while passing the packet to the device driver. They don't have the concept of a pending error.

ERRORS

EADDRNOTAVAIL
Unknown multicast group address passed.:
EFAULT
User passed invalid memory address.:
EINVAL
Invalid argument.:
EMSGSIZE
Packet is bigger than interface MTU.:
ENETDOWN
Interface is not up.:
ENOBUFS
Not enough memory to allocate the packet.:
ENODEV
Unknown device name or interface index specified in interface address.:
ENOENT
No packet received.:
ENOTCONN
No interface address passed.:
ENXIO
Interface address contained an invalid interface index.:
EPERM
User has insufficient privileges to carry out this operation.

In addition, other errors may be generated by the low-level driver.

:

VERSIONS

AF_PACKET is a new feature in Linux 2.2. Earlier Linux versions supported only SOCK_PACKET.

NOTES

For portable programs it is suggested to use AF_PACKET via pcap?(3); although this covers only a subset of the AF_PACKET features.

The SOCK_DGRAM packet sockets make no attempt to create or parse the IEEE 802.2 LLC header for a IEEE 802.3 frame. When ETH_P_802_3 is specified as protocol for sending the kernel creates the 802.3 frame and fills out the length field; the user has to supply the LLC header to get a fully conforming packet. Incoming 802.3 packets are not multiplexed on the DSAP/SSAP protocol fields; instead they are supplied to the user as protocol ETH_P_802_2 with the LLC header prefixed. It is thus not possible to bind to ETH_P_802_3; bind to ETH_P_802_2 instead and do the protocol multiplex yourself. The default for sending is the standard Ethernet DIX encapsulation with the protocol filled in.

Packet sockets are not subject to the input or output firewall chains.

Compatibility

In Linux 2.0, the only way to get a packet socket was by calling socket(AF_INET, SOCK_PACKET, protocol). This is still supported but strongly deprecated. The main difference between the two methods is that SOCK_PACKET uses the old struct sockaddr_pkt to specify an interface, which doesn't provide physical layer independence.

spkt_family contains the device type, spkt_protocol is the IEEE 802.3 protocol type as defined in <sys/if_ether.h> and spkt_device is the device name as a null-terminated string, for example, eth0.

This structure is obsolete and should not be used in new code.

BUGS

glibc 2.1 does not have a define for SOL_PACKET. The suggested workaround is to use:

This is fixed in later glibc versions.

The IEEE 802.2/803.3 LLC handling could be considered as a bug.

Socket filters are not documented.

The MSG_TRUNC recvmsg?(2) extension is an ugly hack and should be replaced by a control message. There is currently no way to get the original destination address of packets via SOCK_DGRAM.

SEE ALSO

socket?(2), pcap?(3), capabilities?(7), ip?(7), raw?(7), socket?(7)

RFC 894 for the standard IP Ethernet encapsulation. RFC 1700 for the IEEE 802.3 IP encapsulation.

The <linux/if_ether.h> include file for physical layer protocols.

The Linux kernel source tree. /Documentation/networking/filter.txt describes how to apply Berkeley Packet Filters to packet sockets. /tools/testing/selftests/net/psock_tpacket.c contains example source code for all available versions of PACKET_RX_RING and PACKET_TX_RING.

COLOPHON

This page is part of release 3.74 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at http://www.kernel.org/doc/man-pages/.


Index

NAME

SYNOPSIS

DESCRIPTION

Address types

Socket options

Ioctls

Error handling

ERRORS

VERSIONS

NOTES

Compatibility

BUGS

SEE ALSO

COLOPHON